Office of the Registrar
Faculty of Engineering and Applied Science (2007/2008)

5003

Ship Structures I

examines longitudinal strength, still water and wave bending moment, shear and bending moment curves, Smith Correction, section modulus calculation, torsion and racking forces; bulkhead and girder scantlings, portal frame analysis by moment distribution and energy method; finite element analysis and the use of Classification Society rules for design of midship section.

CR: ENGI 6002

PR: ENGI 4312

5020

Marine Propulsion

is a second course in marine propellers and ship powering. The purpose of this course is to give students the principles of design and analysis of marine screw propellers and other propulsion devices. The course introduces various marine propulsion devices including conventional and unconventional propulsion systems. It covers methods of propeller design and propeller design philosophy. Emphasis is placed on the design of fixed-pitch propellers based on the lifting line theory and the design of ducted propellers. The student will also develop some insight into the design of other propulsion systems such as waterjets and sails.

CR: ENGI 6020

LH: at least one 3-hour session per semester

PR: ENGI 4020

5312

Mechanics of Solids II

begins with an introduction to earlier concepts then considers strain transformation; deflections of beams and shafts, energy methods; failure theories; buckling of columns and the inelastic behaviour of beams.

LH: at least five 3-hour sessions per semester

PR: ENGI 4312

5420

Probability and Random Processes

includes basic concepts in probability, random variables, multiple random variables, descriptive statistics, random processes and selected applications for engineering.

PR: Mathematics 1001

5434

Applied Mathematical Analysis

examines numerical and analytical solutions of applied mathematical problems in Civil Engineering, problems with higher order ordinary differential equations, stiff equations, systems of ODE, Runge-Kutta methods, boundary value problems, applications of eigen value problems (numerical solutions), Fourier analysis, elliptic, parabolic and hyperbolic partial differential equations and their numerical solutions with engineering applications.

PR: ENGI 4425

5706

Design of Concrete Structures

begins with a review of concrete mix design. Topics include design methods and requirements, strength of rectangular sections in bending, balanced condition at ultimate strength with tension reinforcement, bending with both tension and compression reinforcement; serviceability, deflections, flexural crack control for beams and one-way slabs; shear strength, inclined cracking, and shear reinforcement; bond stress and development of reinforcement; T-sections in bending; members in compression and bending; length effects, lateral ties, spiral reinforcement and longitudinal bar placement.

LH: at least five 3-hour sessions per semester

PR: ENGI 4312

5713

Fluid Mechanics

examines fluid characteristics; fluid statics; buoyancy and stability; kinematics; pressure measurement; continuity, energy and momentum principles; energy and hydraulic grade lines; free jets; laminar and turbulent flow; dimensional analysis; drag on immersed bodies; flow measurement.

CR: ENGI 4913

LH: at least five 1-hour sessions per semester

PR: ENGI 4425

5723

Geotechnical Engineering II

examines shear strength of soil, types of laboratory and in-situ soil tests; immediate and consolidation settlement of foundations; plastic equilibrium in soils; limit equilibrium method; earth retaining structures; introduction to bearing capacity theories; and stability of slopes. Relevant laboratory exercises and projects are also included.

CR: ENGI 6723

LH: 3

PR: ENGI 4723

5800

Electrical Engineering Design

students will work in pairs on small design projects that will require them to follow a hierarchy of design process which includes general product definition, specifications and requirements, functional block diagrams, definition of specification of functional blocks for circuit level synthesis and implementation, system integration, simulation or modeling, testing and verification. The small projects are designed to encourage and motivate students to learn and practise the process of design. The course will culminate in a large design project.

CO: ENGI 5821, ENGI 5854

LC: at least 10 lecture hours per semester

OR: meetings with project supervisor as required

PR: ENGI 4841, ENGI 4855, ENGI 4862

5812

Basic Electromagnetics

includes a review of relevant vector calculus, including the divergence, gradient and curl operators in Cartesian, cylindrical and spherical coordinates, divergence theorem, Stokes’ theorem, and Laplace’s and Poisson’s equations. Topics in electrostatics include Coulomb’s law, potential and energy, conductors, dielectrics, capacitance and electric field boundary conditions. Topics for magnetism include the steady magnetic field, the Biot-Savart law, Ampère’s law, magnetic force, potential and magnetic materials and boundary conditions.

PR: ENGI 3821, ENGI 4430

5821

Control Systems I

includes an introduction to control systems with a negative feedback; mathematical modeling and transfer functions of electromechanical systems; block diagram reduction and signal flow graphs; controller realization using op-amps; transient response analysis; Routh’s stability criterion; basic control actions and response of control systems; root locus analysis and design; frequency response analysis; Bode diagram; gain and phase margins; compensator design in frequency domain; Nyquist stability criterion; A/D and D/A conversion, digital implementations of analog compensators; and an introduction to PID controller tuning methods.

LH: at least four 3-hour sessions per semester

PR: ENGI 4823

5854

Electronic Circuits II

includes an introduction to digital electronics; transient and frequency response of amplifier circuits; feedback amplifier analysis and design, stability and compensation techniques; noise and distortion in electronic circuits; analysis and design of data converters; and an introduction to analog filter design. CAD tools are used to illustrate the analysis and design of electronic circuits.

LH: at least five 3-hour sessions per semester

PR: ENGI 4823, ENGI 4854

5865

Digital Systems

includes concepts, language, tools, and issues pertaining to specification, modeling, analysis, simulation, testing and synthesis of digital systems, including PLD, FPGA, and ASIC devices. Industry standard CAD tools will be used in this course to facilitate system design and testing.

LH: at least ten 3-hour sessions per semester

PR: ENGI 3891, ENGI 4862

5895

Software Design

examines the development process: requirement analysis, design, iterative development, design documentation; an introduction to the Unified Modeling Language: use cases, class diagrams and sequence diagrams; an introduction to software design patterns: creational patterns, structural patterns and behavioural patterns; object oriented, modular decomposition. The course includes a major design project.

LC: at least 15 lecture hours per semester

OR: meetings with project supervisor as required

PR: ENGI 4892

5911

Chemistry and Physics of Engineering Materials II

examines aspects of chemical and physical processes and microscopic structure relevant to the production and use of engineering materials, focusing on metals, alloys, silicates, Portland cement, plastics and adhesives, composites, and wood. Topics include solid-state solutions and compounds, alloy structures, phase diagrams, reaction rates, solid-state transformations, polymerization, oxidation and corrosion, hardness, creep, fatigue, fracture toughness and visco-elastic deformation.

CR: ENGI 3205

LH: at least four 3-hour sessions per semester

OR: tutorial 1 hour per week

PR: ENGI 3911

5927

Mechanical Component Design I

examines adequacy assessment and synthesis of machine elements with a focus on failure prevention, safety factors, and strength; static failure of ductile and brittle materials, fatigue analysis of components. Topics include the design of power screws, bolted connections, welds, springs, and shafts.

CR: ENGI 5926

LH: at least eight 3-hour sessions per semester

PR: ENGI 4312

5931

examines stresses due to combined loads, thin-walled pressure vessels, transformation of stresses and strains, principal stresses and strains (two and three dimensional stresses), Mohr’s circle, theory failures, stress concentrations, energy methods, buckling of columns, thick-walled cylindrical pressure vessels, rotating disks, multi layered thick walled pressure vessels, shrink fits and contact stresses.

CR: ENGI 5312

LH: at least four 2-hour sessions per semester

PR: ENGI 4312

5951

Mechatronics II

focuses on drives and controllers. The topics covered in the course are: electric motors; actuators; control circuits. There is a motors project and 4 laboratory exercises.

LH: at least four 1-hour sessions per semester

PR: ENGI 4951

5961

Fluid Mechanics I

examines fluid statics; fluid flow phenomena; control volume analysis; conservation of mass, momentum, and energy; Bernoulli equation; head losses, applications of conservation laws: flow measurement devices; pipe networks; momentum devices, dimensional analysis, boundary layer phenomena, lift and drag.

CR: ENGI 4913

LH: at least five 1-hour sessions per semester

AR = Attendance requirement; CH = Credit hours are 3 unless otherwise noted; CO = Co-requisite(s); CR = Credit can be retained for only one course from the set(s) consisting of the course being described and the course(s) listed; LC = Lecture hours per week are 3 unless otherwise noted; LH = Laboratory hours per week; OR = Other requirements of the course such as tutorials, practical sessions, or seminars; PR = Prerequisite(s); UL = Usage limitation(s).