14.3 Responding to Installation Procedure Prompts

This section explains the installation procedure prompts and displays.

14.3.1 Selecting Subsets

You must specify which of the PSE subsets you want to load. There may be more optional subsets than can be presented on a single screen. If this is the case, you can choose subsets screen by screen or all at once on the last screen. All of the choices you make will be collected for your confirmation before any subsets are installed.

Note
If you are installing from a RIS distribution area, the number of subsets can vary depending on what products are available in the RIS area and how many subsets they have.

For example: 

The subsets listed below are optional:

     1) High Performance Fortran Support
     2) PSE Networking Kernel Binaries for Digital UNIX V3.2C
     3) PSE System Software
     4) Parallel Programming Environment
     5) Parallel Software Environment Manual Pages

--- MORE TO FOLLOW ---
Enter your choices or press RETURN to display the next screen.

Choices (for example, 1 2 4-6):

Or you may choose one of the following options:

     6) ALL of the above
     7) CANCEL selections and redisplay menus
     8) EXIT without installing any subsets

Enter your choices or press RETURN to redisplay menus.

Choices (for example, 1 2 4-6): 6

To specify more than one number at the prompt, separate each number with a space, not a comma.

Next, the script lets you verify your choice. For example, if you enter 6 in response to the previous prompt, the following is displayed: 

You are installing the following optional subsets:

        High Performance Fortran Support
        PSE Networking Kernel Binaries for Digital UNIX V3.2C
        PSE System Software
        Parallel Programming Environment
        Parallel Software Environment Manual Pages

Is this correct? (y/n):

If the displayed subsets are not the ones you intended to choose, enter n . In this case, the subset selection menu again displays and you can correct your choice of optional subsets.

If the displayed subsets are the ones you want to load, enter y .

14.3.2 Monitoring Displays During the Subset Loading Process

The installation procedure loads and verifies the selected PSE subsets.

When you see the "Verifying" message during the subset installation, the installation procedure is checking to see that the files are copied correctly; it is not an Installation Verification Procedure (IVP) message.

During the installation, if you get errors from the setld facility, see the Diagnostics section of the setld(8) reference page for an explanation of the errors and the appropriate actions to take.

Section 13.5.1 explains how to run the IVP after installation.

In Example 14-1, all the PSE subsets are loaded from CD-ROM.

Example 14-1 PSE Subsets Loaded from CD-ROM Media

Checking file system space required to install selected subsets:

File system space checked OK.

Copyright (c) Digital Equipment Corporation,1995,1996. All Rights Reserved.
Parallel Software Environment for Digital UNIX V1.2-0
Subset: High Performance Fortran Support (PSEHPF120)

Starting installation at Fri Mar  1 17:41:49 EST 1996.

High Performance Fortran Support
   Copying from . (disk)
   Verifying

Copyright (c) Digital Equipment Corporation,1995,1996. All Rights Reserved.
Parallel Software Environment for Digital UNIX V1.2-0
Subset: Parallel Programming Environment (PSEPPE120)

Starting installation at Fri Mar  1 17:42:20 EST 1996.

Parallel Programming Environment
   Copying from . (disk)
 Working....Fri Mar  1 17:42:35 EST 1996
   Verifying

Copyright (c) Digital Equipment Corporation,1995,1996. All Rights Reserved.
Parallel Software Environment for Digital UNIX V1.2-0
Subset: Parallel Software Environment Manual Pages (PSEMAN120)

Starting installation at Fri Mar  1 17:43:16 EST 1996.
There are no installation questions for this subset.

Parallel Software Environment Manual Pages
   Copying from . (disk)
   Verifying

Copyright (c) Digital Equipment Corporation, 1995, 1996. All Rights Reserved.
Parallel Software Environment for Digital UNIX V1.2-0
Subset: PSE System Software (PSEWSF120)

Starting installation at Fri Mar  1 17:43:47 EST 1996.

PSE System Software
   Copying from . (disk)
   Verifying

Copyright (c) Digital Equipment Corporation, 1995, 1996.  All Rights Reserved.
Parallel Software Environment for Digital UNIX V1.2-0
Subset: PSE Networking Kernel Binaries for Digital UNIX V3.2C (PSEKBIN350120)

Starting installation at Fri Mar  1 17:44:18 EST 1996.
There are no installation questions for this subset.

PSE Networking Kernel Binaries for Digital UNIX V3.2C
   Copying from . (disk)
   Verifying

Starting configuration (INSTALL) at Fri Mar  1 17:45:00 EST 1996.
Completing configuration (INSTALL) at Fri Mar  1 17:45:00 EST 1996.
Creating softlinks for PSEHPF120 ...done.

Parallel Software Environment for Digital UNIX V1.2-0
Subset: High Performance Fortran Support (PSEHPF120)

Installation completed at Fri Mar  1 17:45:03 EST 1996.

Configuring "High Performance Fortran Support" (PSEHPF120)

Copyright (c) Digital Equipment Corporation, 1995, 1996.  All Rights Reserved.
Parallel Software Environment for Digital UNIX V1.2-0
Subset: High Performance Fortran Support (PSEHPF120)

Starting configuration (INSTALL) at Fri Mar  1 17:45:04 EST 1996.
There are no installation questions for this subset.
Completing configuration (INSTALL) at Fri Mar  1 17:45:04 EST 1996.
Creating softlinks for PSEPPE120 ...done.

Parallel Software Environment for Digital UNIX V1.2-0
Subset: Parallel Programming Environment (PSEPPE120)

Installation completed at Fri Mar  1 17:45:13 EST 1996.

Configuring "Parallel Programming Environment" (PSEPPE120)

Copyright (c) Digital Equipment Corporation, 1995, 1996.  All Rights Reserved.
Parallel Software Environment for Digital UNIX V1.2-0
Subset: Parallel Programming Environment (PSEPPE120)

Starting configuration (INSTALL) at Fri Mar  1 17:45:13 EST 1996.
There are no installation questions for this subset.
Completing configuration (INSTALL) at Fri Mar  1 17:45:13 EST 1996.
Creating softlinks for PSEMAN120 ...done.

Parallel Software Environment for Digital UNIX V1.2-0
Subset: Parallel Software Environment Manual Pages (PSEMAN120)

Installation completed at Fri Mar  1 17:45:21 EST 1996.

Configuring "Parallel Software Environment Manual Pages" (PSEMAN120)

Copyright (c) Digital Equipment Corporation, 1995, 1996.  All Rights Reserved.
Parallel Software Environment for Digital UNIX V1.2-0
Subset: Parallel Software Environment Manual Pages (PSEMAN120)

Starting configuration (INSTALL) at Fri Mar  1 17:45:21 EST 1996.
Completing configuration (INSTALL) at Fri Mar  1 17:45:21 EST 1996.
Creating softlinks for PSEWSF120 ...done.

Parallel Software Environment for Digital UNIX V1.2-0
Subset: PSE System Software (PSEWSF120)

Installation completed at Fri Mar  1 17:45:38 EST 1996.

Configuring "PSE System Software" (PSEWSF120)

Copyright (c) Digital Equipment Corporation, 1995, 1996.  All Rights Reserved.
Parallel Software Environment for Digital UNIX V1.2-0
Subset: PSE System Software (PSEWSF120)

Starting configuration (INSTALL) at Fri Mar  1 17:45:39 EST 1996.
There are no installation questions for this subset.

Using the existing port number (57039) for basic farm `psefarm'

Updating /etc/rc.config ...
Updating /etc/inetd.conf ...

Verifying farm `psefarm'...
Local farm daemon for farm `psefarm' is active.
Completing configuration (INSTALL) at Fri Mar  1 17:45:50 EST 1996.
Creating softlinks for PSEKBIN350120 ...done.

Parallel Software Environment for Digital UNIX V1.2-0
Subset: PSE Networking Kernel Binaries for Digital UNIX V3.2C (PSEKBIN350120)

Installation completed at Fri Mar  1 17:45:51 EST 1996.

Configuring "Kernel Binaries for Digital UNIX V3.2C" (PSEKBIN350120)

Copyright (c) Digital Equipment Corporation, 1995, 1996.  All Rights Reserved.
Parallel Software Environment for Digital UNIX V1.2-0
Subset: PSE Networking Kernel Binaries for Digital UNIX V3.2C (PSEKBIN350120)

Starting configuration (INSTALL) at Fri Mar  1 17:45:51 EST 1996.

    ************************** INSTALLATION NOTE **************************
    *                                                                     *
    * To complete the installation, you have to link the new .o files     *
    * supplied by this subset to the kernel's BINARY directory and relink *
    * the kernel.  You can use the /usr/sys/UDP_PRIME/Install shell       *
    * script to save the original .o files and link the new .o files.     *
    * The following commands give an outline of the steps:                *
    *                                                                     *
    * % su                                                                *
    * # cd /usr/sys/UDP_PRIME                                             *
    * # ./Install                                                         *
    * # cd /usr/sys/FLECT1                                                *
    * # rm vmunix*                                                        *
    * # make                                                              *
    * # cp vmunix /vmunix                                                 *
    * # shutdown -r +5                                                    *
    *                                                                     *
    * Refer to the /usr/sys/UDP_PRIME/README file for further details on  *
    * installing and de-installing the PSE Networking Kernel Binaries.    *
    *                                                                     *
    ***********************************************************************

Completing configuration (INSTALL) at Fri Mar  1 17:45:52 EST 1996.

Once the installation procedure is complete, enter the following command at the C shell (csh) prompt: 

# rehash

The rehash command updates the search paths.

Note
To complete the installation of the PSE Networking Kernel Binaries subset, you must reconfigure the kernel. For information on configuring the PSE Networking Kernel Binaries subset, see Section 13.4.

If a PSE cluster database has been defined and it includes this system as a member, run the following command to configure the PSE cluster daemon: 

# pseconfig add farmname

Otherwise, use psedbedit to define your PSE cluster database or to add this system's nodename to the database, prior to running the command previously described.

For More Information: